水基银纳米线导电墨水和大尺寸柔性透明导电薄膜的制备

以银纳米线(AgNW)为导电材料,添加羟丙基甲基纤维素(HPMC)和氟碳表面活性剂FSO-100制备了水基导电墨水,使用迈耶棒在聚对苯二甲酸乙二醇酯(PET)膜表面刮涂制备了柔性透明导电薄膜,研究了AgNW、HPMC和FSO-100等组分的添加量对透明导电薄膜光电性能的影响。结果表明,表面活性剂FSO-100可以明显提高导电墨水对PET衬底的润湿性,但过量后会使方块电阻上升;HPMC的加入可以消除AgNW的团聚,但过多的HPMC会提高薄膜的方块电阻;AgNW含量增加后,薄膜的方块电阻和透过率均随之下降,在AgNW浓度2.6 mg/mL时,透明导电薄膜的方块电阻为12Ω/sq和550 nm的透明导电薄膜透过率为94.02%,品质因子可达448.63,薄膜的粗糙度均方根为7.28 nm,并可在1000次弯折后保持光电性能不变,在可穿戴器件、柔性有机发光二极管等领域有很大的应用前景。     

Ti-20Al-22Nb合金的凝固组织转变及力学行为

采用熔模铸造方法制备了名义成分为Ti-20Al-22Nb(at%)的合金,分别对铸态、热等静压及退火态进行了显微组织及室温拉伸性能分析。结果显示,合金由β基体、针状α2相及少量O相组成的,铸态下为粗大的魏氏组织,由于非平衡凝固,原始晶粒内部组织转变不完全,组织中的疏松缺陷及组织不均匀导致合金低的塑性；经过α2+β/B2两相区热等静压消除了疏松缺陷,原始晶粒内部充分析出细小针状的α2相,组织均匀性提高,合金的拉伸延伸率由2%提高到5%；经过α2+/B2+O三相区退火热处理,过饱和β相向平衡态转变,通过包析转变β/B2+α2→O,在针状α2相周围形成环带状O相,合金的延伸率提高到11%。     

Dynamic optimization for gas blending in pipeline networks with gas interchangeability control

The increasing penetration of unconventional gas and liquefied natural gas poses an operational challenge on existing regional gas networks for gas quality problems. A new dynamic model for natural gas pipeline network with multiple supplies is presented with a special emphasis on gas interchangeability control. Wobbe index serves as gas interchangeability indicator and is calculated by equations derived from rigorous composition-based partial differential equations. Disjunctive formulation is applied to represent different modes of gas blending due to gas reversal, and the disjunctive model is then reformulated as a nonsmooth model with min/max and absolute value functions, which is solved by a gradient-based nonlinear program solver after smooth approximation. Moreover, a heuristic algorithm is proposed to tune the penalty parameters in order to focus on different penalty terms while keeping the model well-conditioned. The developed model and strategy are first tested with a small pipeline network model and then extended to a large model. The results show that the model can effectively manage gas interchangeability issues in pipeline networks within reasonable CPU time.     

费托合成尾气脱碳工艺选择及试车问题分析与优化

综述了不同尾气脱碳工艺的优缺点及适用条件,指出热钾碱法是目前较适用于大型费托合成尾气中CO2脱除的方法。介绍了处理尾气规模为60万m3/h的某热钾碱脱碳工艺流程,针对该装置在投料试车过程中出现的再生系统能耗高、费托合成尾气水洗效果差、吸收塔填料易堵塞及再生气排放非甲烷总烃超标等问题,进行了原因分析,并提出了一系列工艺调整及设备改造措施。实际运行结果表明,所采取的优化措施能够有效解决上述问题。     

基于水泥除尘+脱硝流场的CFD数值模拟研究

随着社会环保意识的增强,大气污染物的排放标准也日益严格,这给环保工程带来了极大的潜在市场。脱硝反应器设计作为SCR脱硝工艺中除了催化剂的另一核心,在水泥行业没有更好的催化剂被研发出来之前,想要脱硝设备的性能得到极佳的发挥,在高温高尘区布置除尘+脱硝设备已经是工程上的一个选择,而在高尘区要保证催化剂的稳定、高效运行,流场的优化必不可少。本文针对某水泥行业除尘+脱硝项目,采用CFD软件对其流场进行数值模拟,并给出导流板的优化设计方案。结果表明:在电除尘器上进气口布置合适的导流板,使得进入电场的烟气分布均匀;同时在整流格栅前添加导流板,脱硝反应器内的流场也得到了极大改善。因此,采用CFD软件数值模拟对水泥行业除尘+脱硝有着重要的意义。     

Oval cuboid TiO2 particles with mesoporous structure fabricated by using fluorinated block copolymers as templates with photocatalytic performance

In this work, a poly(ethylene glycol)-b-poly(1H,1H,7H-dodecafluoroheptyl methacrylate) (PEG-b-PDFMA) block copolymer was first synthesized by the reversible addition−fragmentation chain transfer (RAFT) polymerization. Then a novel facile approach was developed to fabricate oval cuboid TiO₂ particles with mesoporous structure by using the PEG-b-PDFMA block copolymer as a template and titanium tetrabutoxide (TBOT) as a precursor, followed by evaporation-induced self-assembly (EISA) process and calcination process. The results show that the PEG-b-PDFMA block copolymer can control the oriented assembly of nanoparticles and act as templates for the formation of a mesopore. It is found that the mass ratio of TBOT/PEG-b-PDFMA and water content in the solution have a significant influence on the morphology of TiO₂ particles. When the mass ratio of TBOT/PEG-b-PDFMA is 0.25/1, oval cuboid TiO₂ particles with mesopores are obtained, which exhibits a high photocatalytic activity for the degradation of methylene blue (MB) dye under UV light irradiation.     

A miniature triaxial apparatus for investigating the micromechanics of granular soils with in situ X-ray micro-tomography scanning

The development of a miniature triaxial apparatus is presented. In conjunction with an X-ray micro-tomography (termed as X-ray μCT hereafter) facility and advanced image processing techniques, this apparatus can be used for in situ investigation of the micro-scale mechanical behavior of granular soils under shear. The apparatus allows for triaxial testing of a miniature dry sample with a size of \mathrm{8}\hspace{0.17em}\mathrm{mm}\times \mathrm{16}\hspace{0.17em}\mathrm{mm} (diameter \times height). In situ triaxial testing of a 0.4–0.8 mm Leighton Buzzard sand (LBS) under a constant confining pressure of 500 kPa is presented. The evolutions of local porosities (i.e., the porosities of regions associated with individual particles), particle kinematics (i.e., particle translation and particle rotation) of the sample during the shear are quantitatively studied using image processing and analysis techniques. Meanwhile, a novel method is presented to quantify the volumetric strain distribution of the sample based on the results of local porosities and particle tracking. It is found that the sample, with nearly homogenous initial local porosities, starts to exhibit obvious inhomogeneity of local porosities and localization of particle kinematics and volumetric strain around the peak of deviatoric stress. In the post-peak shear stage, large local porosities and volumetric dilation mainly occur in a localized band. The developed triaxial apparatus, in its combined use of X-ray μCT imaging techniques, is a powerful tool to investigate the micro-scale mechanical behavior of granular soils.     

帮坡角变化对露天矿采剥量以及经济效益的影响

露天矿最终帮坡角是影响露天矿安全生产的主要因素之一,也对露天经济效益产生重要影响,特别是对大型深凹露天矿的影响尤为突出。在保障露天矿安全生产条件下,本文通过优化矿区不同帮坡角条件下的最终境界,研究帮坡角变化对矿山岩石剥离量、矿石采出量以及经济效益的影响。结果表明,随着帮坡角的增加,最终境界内的岩石剥离量、矿石采出量可能增多也可能减少,但经济效益呈现增加趋势。     

镀锌层硅酸盐+虫胶复合转化膜的制备和表征

目的阻碍热镀锌板出现白锈,提高镀锌层的耐腐蚀性能。方法采用正交试验法优化出添加虫胶水溶液的有机无机复合钝化液。通过电化学Tafel极化曲线、交流阻抗(EIS)、乙酸铅点滴和中性盐雾试验,对比分析基体、硅酸盐+虫胶复合钝化膜与铬酸盐钝化膜的耐腐蚀性能。采用摩擦法测试对比分析基体和无铬钝化膜试样的附着性能,并通过扫描电子显微镜、X射线光电子能谱和红外光谱对形貌和结构进行分析。结果添加虫胶水溶液的复合钝化膜表面平整致密,72 h中性盐雾试验后的腐蚀面积小于10%。乙酸铅点滴试验和电化学测试显示,复合钝化膜的耐腐蚀性能较基体好。附着力试验测试显示,复合钝化膜具有良好的附着能力。结论因为复合钝化液中的虫胶与硅酸盐交织为O—Si—CH_2结构,与金属离子结合生成致密的膜层附着在镀锌层表面,使得复合钝化膜致密平整,且使腐蚀过程得到了强烈的抑制。     

遗传算法和模矢法结合的概率积分法参数反演方法

遗传算法在反演概率积分法预计参数时从参数取值范围内的串集开始搜索,并使用弹性策略来维持群体的多样性,使得算法可以跨过局部收敛的障碍,向全局最优解方向进化;但这种概率化的寻优算法存在局部探索能力差、结果不稳定的缺陷,只能获得问题的近似最优解。模矢法是一种降梯度算法,算法局部探索能力强、收敛快;但这种算法对初值选取敏感,初值选择不当易陷入局部极值。本文提出并实现了一种模矢法与遗传算法结合的组合算法:先使用遗传算法求得参数的全局近似最优解,然后将近似最优解作为探索初值,使用模矢法获得参数的稳定、精确最优解。研究结果表明:组合算法反演概率积分法预计参数的精确度高、收敛快、稳定性好,综合性能较遗传算法和模矢法有明显优势。